Archive for the ‘15mm’ Category

st1

This is one of the latest 15mm offerings from Zvezda and as you would expect ,

the kit is plastic and simple to assemble.

The Sturm Tiger was created as an infantry support vehicle, specifically to

destroy urban targets(buildings). The Germans had learnt to their bitter cost

that street fighting was not easy and they needed something to even the balance.

Thus they created the monster known as the Sturm Tiger. It consisted of a

380 mm Raketen-Werfer 61 L/5.4, a breech-loading rocket launcher which fired

1.5m long rounds(weighing 376kg) and delivered 125kg explosive charge. The round

could flatten a factory !

The vehicle used the Tiger tank chassis as its base.

Unfortunately for Germans they were not available until the end of the war and

only took part in action in the Warsaw Uprising, the battle of the Bulge and the final

battle for the Reichswald. Only 19 were built.

I have painted mine up in dot camouflage but its hard to see with all the weathering. I

wanted to give the vehicle a just driven through an destroyed building look in a very

grimy urban scene. Perhaps just about to fire a huge round on some unsuspecting defenders

in a house ?

Click on any picture to enlarge.

st2

st3

st4

st5

puma1

The Puma or Sdkfz 234 Sonderkraftfahrzeug was a fast, well armed German reconnaissance

car during WW2. They were produced from 1943-1944 with a well armed 5cm L/60 gun and a

Tatra V12 diesel engine which enabled the vehicle to have a top speed of about 55 mph.

The vehicle had 8 independent steerable wheels and a front and rear driving seat, enabling

a quick exit from danger when needed.

These 3 models are made by Skytrex(Command Decision) 234/2`s and are made of metal. Personally I think

plastic would have been a better idea as they weigh quiet a bit. I have painted all three in

Normandy campaign colours and left the exact division open to interpretation, thus the

minimal markings.

Hope you like them ?

Click on any picture to enlarge.

puma2

puma3

puma4

puma5

I have not gone over board with the Panthers and Shermans as they are meant for quick gaming.

Just enough to get me back into the flow.

The jeep and truck will be used for objective markers.

finish1

finish2

finish3

finish4

finish5

Its been a while ,but finally the tanks are rolling out across my battle board again. The dust is being blown off the paint pots and the brushes are being nursed back to life.

Anyway just a quick picture update on what is on the painting table as it pours down with freezing rain outside.

First up as you can see a friend has got me painting his tanks from the Gale Force 9 board game.

war2

Two 15mm basic plastic Shermans from the board game.
war8
Three, 15mm plastic Panthers(2 for the board game and a Zvezda model).
war4
Three, 15mm metal Skytrex Pumas.
war3
A 1/72 scale Revel jeep and 15mm plastic Zvezda Sturm Tiger.
war7
1/72 Revell American lorry, wrecked.
war5
A 15mm metal Citroen car by Loic.
war6
An O Gauge train for a Bolt Action diorama.
war1

Hopefully now that I am back in the swing of things you should get some more updates shortly.

tankart-1-3rd-ed-

I have been after this book for a while and
finally managed to win an ebay auction at a
reasonable price(£30). Its sounds expensive but
its out of print and highly sort after by the modelling
community.

For your money you get 288 pages of mouth watering, glossy
pages. The first 34 pages are broken up into describing in
simple detail the techniques used in the book and it is all
supported with easy guide pictures and steps.

The remainder of the book is divided into eight sections, each
section covering a build of a different vehicle, showing the
painting and weathering.

I have read a lot of guides and books covering afv painting and
weathering techniques but this is simply the best so far. This book
describes everything in steps and pictures where other books skip stages
or keep back vital information like it is one great secret. Plus you
don’t need to be an expert as its written and explained so well anybody
can learn from it.

My only complaint is that there is so much stuff in this book I
don’t know where to start lol.

This is a must buy for any afv modeller and there are 3 other books
available as well but sadly also out of print. The remaining books
cover allied armour as well.
Hopefully these books will be re-printed in the near future and
everybody can get their hands on a copy.

hairspray

Windmill1

Ok its finally finished.

I ended up going for a simple plasticard base and just

basic vegetation. If the base had been any bigger it would

of limited the amount of places I could of used it on a terrain

board.

So to sum it all up. Due to lack of 15mm windmills on the market

in the Normandy style, I decided to scratch build one. The tower is

made from plastic tube and has modelling clay on the outside giving

the stone effect. The top of the windmill is styrene with modelling clay

on the outside giving the tile effect. I also used balsa wood to make the

sail connection.

The sails are borrowed from another 15mm manufacturer of windmills and I used

an iron rod to connect the sails to windmill. Thus the sails actually turn and

are not fixed in place. The door on the windmill is balsa wood and the windows

are pinched from an “N”guage model railway building.

I tried to go for the overall look of recently abandoned.

Anyway it was lots of fun making it and hope you like it.

Windmill2

Windmill3

IMG_0871a

Things are on the move finally. I finished the top

which is styrene covered in modelling clay. I also managed

to get the connection between the sail and mill sorted

which took an eternity to get just right.

Its presently had a few starter coats of paints on it and I am

about to base it on something a bit bigger. The basing will

help it stand up and keep it safe from big clumsy hands like

mine.

More soon.

IMG_0873a

Untitled-1

I have been wanting a windmill to sit on

my terrain boards for ages and fed up with the

lack of ready made terrain to do the job I

decided to have a go at building one myself.

So here is the plan. First,I cut off a small

length of black plastic drainpipe tube. After much

thinking I decided to achieve the stone effect with

DAS modelling clay as it gave me the ability to get

exactly what I was after. Its simply moulded around

the drainpipe and I used a small knife to mark out

the stone relief, windows and door.

Next up I need to create a roof, build some door and

window frames plus add lots of paint. I have found a

windmill sail from a bargain bucket which can be adapted

to the correct type. This should help speed things up.

Below is the DAS modelling clay after sculpting.

IMG_0769

Only got to wait 3 days now for it to dry lol.

I bought this from Peter Pig a while back and

I have finally finished it to my satisfaction.

You basically get the resin cast as in the picture

below and its up to you from there on in.

What I really like about the model is the crew

members that have tried to bail out too late.

Click on any picture to enlarge.

IMG_0375a

Damt1

Damt2

Damt3

I think a bit of background is needed to start

this post off and to explain why I happened to have

six Tigers tanks just lying about !

I recently attended a wargames event with two friends

and we were admiring a beautiful WWII board set up for

FOW which happened to have an SS Division fielded on the

board. Admiring the SS Tigers my friend pointed out he needed

to buy some more Battle Front Tigers for his army and the lad

running the table pointed out they were not Battle Front Tigers

and belonged to a different manufacturer ! We argued against this

,until the lad let us kindly handle the tanks which resulted in

humble pie on our behalf. This got us all thinking because at a

distance of two feet none of us could tell the difference.

So knowing I had two different types of 15mm Tigers at home and

my mate had a third manufacturer we decided to do a bit of research

and buy the remaining 3 on the market.

The plan was simple. Compare the 6 main manufacturers of 15mm Tiger

tanks(sorry if your product is not included) and then devise a cunning

plan to test our eagle eyed wargamers to see if they can spot the difference.

The Review

The six manufacturers in question were:

  • Battlefront.
  • Skytrex.
  • Forged in Battle.
  • Peter Pig.
  • Zvezda.
  • Plastic Soldier Company.

Ok a word of warning on my review. It is based on the kits I had

available to me at the time and there are other kits produced by

the same manufacturers which come in varying periods of WWII and

materials.

Here are the six kits below :

Click on any picture to enlarge.

Tiger61

So from left to right a quick summary.

First up was the Plastic Soldier Company

This tank came from a box of four tanks priced at £19.50 plus 10% postage.

Its plastic and comes with options to build either early, mid or late which is

a really nice touch. You also get two crew members and stowage options. The

only one query/criticism was the width of the tracks ? They seemed a little

narrow to me ? Plenty of hatches.

Second was Forged in Battle

This is a resin cast that costs £7.50 plus £4 postage. First impression was

that the tank looked a little to narrow. Its also comes based which I am

not a big fan of. Its made of 3 main parts so assembly is quick and you get

one crew member.

Third was Peter Pig

You get a totally metal product coming in at £7 plus £3 postage. It has 6 parts

in total and not a bit of flash on the parts so well done. The tracks have

a clever insert so you are able to attach them in the exact position. You also

get two hatches and a crew member.

Fourth is Skytrex(Command Decision)

Price was £7.70 plus £5 postage. All metal parts and very solid. Criticisms would
be a lot of flash on the rear of the tank and no crew.

Fifth is Battlefornt

Mixed parts of resin and metal and costing £8.99 and £2.75 postage. Best thing

about this was out of all the tanks is gave the best opportunity to customise in

my view. Down side was that some of the parts are very small and extremely fiddly

to attach. Lots of hatches and crew. This is the early version of the Tiger.

Last and not least is Zvezda

Totally plastic and quick to assemble. Cost wise, £6.95 including postage. You

get no crew.

TIGER62

Tiger63

Tiger65

So what’s my verdict ?

Well if I go onto the various forums for 15mm Wargaming and ask

peoples opinion on what Tiger to buy each manufacturer or supporter

of that product sings the praises of their model saying how great it

is compared to the others on the market, but the proof is in the pudding.

And in this case the pudding is going to be the finished model, the thing

you will see at two feet away on a board.

So I challenge you to identify the 6 Tiger tanks that appeared in
my earlier post. What I`m trying to prove is that once on the board nobody
cares who made the model because its all about the finished look and
playing the game, no matter what the bumf in the brochure tells you.

Follow the LINK